Search results

Seemingly stupid problem but quite frustrating if i want to set a recirculating schedule. When i set time and date in settings - then return to it it's always back to initial 2000-00-00. I did a factory reset and went through initial setup again but no avail, time and date wont stick. Anyone...

the tank is adjustable at 50psi - would it make sense to try 75 while i wait to source a gauge? also where should said gauge be hooked up?

I have a 150psi pressure relief valve and a small expansion tank (http://zilmetusa.com/Thermal-ZEP1) I noticed some wetness around the relief valve and went ahead and replaced it. However the same activity is happening, small water releases from the pressure relief valve after use. Is this...

ok, feels like I'm finally getting my head around this with everyone's help, i confirmed using a magnet that i have lead on the outside. So I guess that leaves the question of whether I have XHCI or regular 4". Does anyone know the OD of these standards?

Hi Sylvan - are you referring to removing the old flange? or the actual CI elbow? I do not have access to the piping aside from the top so replacement options are limited. Is there an offset caulked CI floor flange?

Appreciate the advice, the pipe i have appears to be lead and is part of original construction from 1967 it's 4"ID 5"OD and start to curve almost immediately. I have some flexibility in terms of height but can't do a full 2" rise. That means that the adapter should be an inside fit adapter that...

Right - my pipe is slightly above the floor level, it’s also an elbow so I don’t think I can cut it much, photos for clarity

Correct me if I’m wrong but all of these adapters have 4” openings, my ID is 4” so I don’t believe these will fit. I need something that is an inside fit

I’m in the middle of a bathroom remodel and am facing a small dilemma. The existing 4” ID cast iron connector has a busted flange and is 11” from the wall vs the 12” I need for my Woodbridge toilet. I’ve found a few offset adapters but they would raise the toilet about 2” higher which wouldn’t...

thanks Terry! here is the tub https://www.wyndhamcollection.com/showers-tubs/ursula-59-soaking-bathtub-by-wyndham-collection-white__wc-btk1511-59.aspx

So my recently installed (not by me) tub is starting to leak at the drain. I wanted to take the opportunity to replace the drain at this juncture anyway. The new drain comes with 2 rubber gaskets (and no instructions) should I just use the gaskets or is advisable to use putty/silicone as well?

Ha, great minds!

i need a super low profile P-trap (every inch lowers the ceiling of the family room). I bought this one and am trying to connect it to a bathtub drain: https://www.amazon.com/gp/product/B00VV4PLF8/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

I’m not thinking straight, lol. Is stainless ok in a dwv application or will it eventually rust through?

That looks promising but I think wrong material - won’t glue with abs/pvc

Can I mix and match all these with ABS?

So I have a 1.5” slip connection on one side and would love to connect it to a 2” female threaded. Space is super tight so ideally looking to do it in a single adapter but can use two provided they are low profile, any ideas?

Appreciate your help, thankfully I'm outside SF so the laws are not applicable to me. Based on this map I should be between 52-57 for water temp https://assets.supply.com/ul_pdfs/284997_groundwatertemperaturemap.pdf

I need to relocate my existing 80gal tank unit. Given it's 11+ years old it seems like a replacement is in order as well. As it stands, hot water takes a long time to reach the kitchen so clearly a recirc is needed. Gas line access is easy so that's not an issue. Hoping for a 9+gpm unit for a...

My toilet is on the second floor and I am attempting to sheetrock the ceiling underneath it. There is currently a 3” quarter turn, long sweep coming off the toilet that hangs about an inch too low, is there any creative solutions (don’t have to be code but do have to be functional)?