Search results

Yes they easy way to do it was build from inside outward. I connected the 2 filter heads ahead of time, then put the brackets on them to mark the Pleiades for the bracket screws. Then mounted them and works outward with rest of pex. Unfortunately I was off a tad as you and see the, slightly off...

I think I know the answer to this and I am sure I will probably get different answers as my friend Google gave me mixed results. I have water filters that have 1 inch stainless steel female connections. I used 1 inch male to 3/4 Propex brass fittings with teflon thread tape. Not sure why I...

Thanks. Eager to get this done. Have another 2 Saturdays of work before I can cut over the water to the new pipes.

Has zero issues piping yesterday with the tool, Uponor pipe and fittings. Was able to easily get pipe to the shoulder with plenty of time to spare. An example shown.

So we are piping now (taking lunch break) and they all look perfect. The test fittings I used were Sharkbite pex-a, using the Uponor fittings today were no issues. I also re-greased the M12 as I was not happy with how the grease applied yesterday. I will post some pics later as we are doing the...

Here are most of the tests I did and my concern on them not being flush with shoulder. I also have a new Milwaukee pipe cutter I am using and find you really need to be rock steady to get a perfectly flat cut, I find several time it has a very slight angle to it.

If I did switch I would do cinch and use Boshart Stainless fittings. I have a few tight spots the crimp may be a hassle. I did follow the Uponor instructions, they say put the tool in without pushing, run it through 9mexpqndsilns and it the pipe is filling in by then,I found running another 3...

Thanks I will take some pics in AM so post to make sure I am good. My wife think I am being to anal about making it perfect

Been a while and wanted to follow up. I have everything and ready to get started. Decided to pick a few fitting and a stick of 3/4 to test and practice. I have all Uponor pipe, rings and fittings. I am using the M12 tool and was surprise how little time you have to get the fitting on. I read the...

Was panning on that as well. I think the one section I will pre-make then cut out the copper to avoid it getting in the way. I was trying to do parallel runs everywhere possible to make the cutover easier.

I thought this class windows had closed. The municipal water did several studies over 5 years ago as the increase of issues had everyone blaming water. The reports basically said, ntorhe water in general and likely poor materials or installs. I think BS and years ago the water was probably not...

I am rerouting large portions, there is just no way to get to master shower without running down the small space between the 2 joists. Routing through attic is not practical as I would need to remove 21 inches of insulation.

I am replacing all the copper with PEX. Have had 5 pinholes in 6-7 months. I put an arrow in the narrow cavity I need to run PEX in. That cavity is right over the wall where the pipes go to the master shower. I suspect that is why they did not sister the joists there as they would have lost...

I like that idea, may look at that and make sure I am not compromising the joists. Other option I was thinking was using a section of brass nipple with an elbow and just putting PEX expansion fittings on end end, then I can thread the nipple into the elbow.

So I have 2 tricky place I need to put a PEX-a elbow. I have limited space and will have to expand one pipe then slide it through 2 joists (about 4 inches apart to get it into the small space the elbow and pipe will be. Since I have not done PEX-a before how long from the time I pull off the...

I was thinking that, but want to avoid using any of the 38 year old portions of pipe. For the tub (black felt paper one) I am leaning toward doing that. the main shower I am leaning toward replacing both valves with pex vales and then having a 1/2 press to p1/2 Pex-a pressed on and do all pex...

I was all set to go Rehau, and wanted to stick with mfg. fittings, but they had a few backordered for months so switched to Uponor and all my fittings, bend supports, valves etc. are Uponor so if there is a problem I don't have to have them saying I used an OEM fitting. I actually get started...

Been fighting some what I think are bad copper fitting as I try and redo the copper around the water heater. In the mean time the Pex was support to be delivered 2 days ago and they screwed up, some hopefully Tuesday now. Drilled some of the new holes to route the pex in parallel. My plan is to...

The valves are Moen Posi-temp valves installed during remodel 7 years ago that is why I am trying to preserve the valves. Part of me want top pull the valves and put in Pex version, but the thought of cutting the studs and doing this from behind seems trickier than I may be up to. I wish I...

I am repiping my home. 37 year old copper that has had 5 pinhole leaks in the last 6 months. Going with Pex-A. I am not in the mood to pull the shower valves since they are 7 years old and were put in when we remodeled at that time. I would like to keep the copper coming out the sides of the...