Recent Activity

Activity stream for all registered members at Terry Love Plumbing & Remodel DIY & Professional Forum.

  1. Terry replied to the thread New remodel bathroom.

    I didn't say he couldn't install it. I just answered what to look for on the spec sheets as an example. I'm sure if it's sold in the US,...

    Dec 13, 2018 at 12:38 AM
  2. bob_cville posted a new thread.

    Venting Issue With Shower Remodel

    We are remodeling our Master bath with a plan of changing the 3 foot by 4 foot one piece fiber glass shower to a tiled shower with two...

    DSC_0166 (2).jpg Resized_20181211_170142001_3113.jpeg DSC_0164 (2).jpg

    Forum: Plumbing Forum, Professional & DIY Advice

    Dec 12, 2018 at 10:47 PM
  3. seandunn replied to the thread Can i install one of these light on an exterior wall and be within code and fine with an inspector.

    Thank you, i think it will try that and just see what the inspector will say about it. thanks again guys!

    Dec 12, 2018 at 10:17 PM
  4. seandunn liked Stuff's post in the thread Can i install one of these light on an exterior wall and be within code and fine with an inspector.

    If you came through the back then NM might be OK. If from the bottom then UF as it would be exposed.

    Dec 12, 2018 at 10:15 PM
  5. Stuff replied to the thread Can i install one of these light on an exterior wall and be within code and fine with an inspector.

    If you came through the back then NM might be OK. If from the bottom then UF as it would be exposed.

    Dec 12, 2018 at 9:11 PM
  6. Dave Alessandria replied to the thread Tankless Combi Boiler First Start.

    I’ve got a lot of old cast iron radiators all on one zone for the whole 2300 sqft home so I think I should have enough of thermal mass...

    Dec 12, 2018 at 7:41 PM
  7. Eddie Hong replied to the thread New remodel bathroom.

    Thank you Terry, sorry for the late reply. I think my friend just bought one of those toilets its a off brand and price was right. So...

    Dec 12, 2018 at 7:24 PM
  8. jadnashua replied to the thread Methane gases in a sump pump pit - question.

    A month or so ago, the local gas company was around. They'd just repaired a leaking gas line nearby, and asked if they could check my...

    Dec 12, 2018 at 7:03 PM
  9. djarchow attached a file to the thread Yet another basement vent question.

    In looking at my previous attempt at drawing out the plumbing in our master bath and what is in the basement, I see it wasn't very...

    plumbing2.jpg Dec 12, 2018 at 7:02 PM
  10. jadnashua replied to the thread Closet Flange Rough-In Before Pouring Concrete.

    My preference would be to make the stubout much taller than needed and put a cap on it so it can be tested. Then, cut it off where...

    Dec 12, 2018 at 6:53 PM
  11. jadnashua replied to the thread Adding baseboard.

    Lots of windows? Any of them low-E? No housewrap? Do you get a breeze through the receptacles and switch boxes? What's underneath...

    Dec 12, 2018 at 6:50 PM
  12. seandunn liked Stuff's post in the thread Can i install one of these light on an exterior wall and be within code and fine with an inspector.

    Never done one of these but it looks like there are many that use the same wall mounting bracket. Directions seem to say to use an...

    Dec 12, 2018 at 6:35 PM
  13. seandunn liked kreemoweet's post in the thread Can i install one of these light on an exterior wall and be within code and fine with an inspector.

    It seems to be designed to be hard-wired, with just a cable entering a wiring compartment in the fixture. No box needed, and probably...

    Dec 12, 2018 at 6:35 PM
  14. kreemoweet replied to the thread Can i install one of these light on an exterior wall and be within code and fine with an inspector.

    It seems to be designed to be hard-wired, with just a cable entering a wiring compartment in the fixture. No box needed, and probably...

    Dec 12, 2018 at 6:11 PM
  15. Dangerous posted a new thread.

    Fleck 9100 Gear Positions and Removal

    First: The hole through which the upper gear enters to back plate has cracked. I've ordered a new back plate, so to prepare I'm looking...

    Forum: Water Softener Forum, Questions and Answers

    Dec 12, 2018 at 6:02 PM
Loading...