Recent content by Hiluxsurf

That's correct - all wired up now - thanks Reach4

Reach4 - you come to my salvation once again! See attached images - one showing existing, and one showing what I think I can do - splices shown as blobs. Look right to you?

So - have a wiring question about going from a 4 wire (3+G) cable to a 3 wire (2 +G) cable. As is there is a designated circuit which comes from the breaker (double pole) with 3+G (Old cable, red, white, black and G) to an outlet. The cable OUT of the outlet other side goes to a dishwasher -...

Thanks all - no vacation setting but I can move to 'Pilot' mode - will that have the same effect?

Hi I have a large gas water heater/tank - and need to do a very quick (5-10m) repair on a hot water line on the top floor of the house. The water heater does not appear to have a shut off valve on the hot water out of the tank, only on the cold water into the tank. If I turn off the cold...

Thanks - that's what I figured also - just wondered if there might be some pressure equalisation issue or something. I'll take a closer look at the capping off

Hi All Replacing tub but to save money want to re-use the existing Hansgrohe Axor fittings (fitted on tap deck) - have a question about the rough out. It is a 4 hole fitting - hot/cold/filler and showerhead - I don't really want to use the shower head so want to use it as a three hole unit...

Thanks all - will see if I can connect the PEX right to the filler as suggested...

Thanks for the extra info - to make sure I understand you correctly - you connected the miniball valves to the faucet direct, and then the PEX to the valves - with no braided/corrugated flexible lines? If so - interesting - might give that a go! And any particular benefit to copper stubs vs...

Thank you for the info... The freestanding tub has a removable panel on the outer wall - so there is space to access plumbing between the outer and innerwall (the faucets will be fitted on to a tap deck in the tub - once I've drilled the holes in the deck) - so I was thinking the PEX would come...

Hey - PEX newbie so forgive the dumb questions. Existing tub has 1/2 copper teed off a main 3/4 copper supply line. Thinking I will use Sharkbite 1/2 - 3/4 elbow to go from a 1/2 copper to 3/4 PEX (too chickenS=-t to learn solder for this one job) Think the ID of the 3/4 PEX more similar to...

Thank you so much Wayne - I am so grateful to have found the right way forward. Appreciate you taking the time. The shower drain (though you can't see in the photo) actually runs beneath the joists - and I just looked and think enough clearance for the 1 1/2" to run to the trap under the joist...

Thank you, Wayne, for making that clear....now, the plot thickens! I just got a ladder out and went up on the roof - and I can see there is another vent - this must be a dry vent for the shower - so that explains the 12ft arm. So I'm assuming that's all fine? ie it isn't acting (primarily) as...

Thanks John and Wayne - appreciate the rapid replies. Wayne - couple follow up below....to ensure I have understood On 1) - so I will add a new 3" wye and run a 1 1/2" line to the tub - correct? And ok just to cap the existing/wrong 1/2" wye? On 2) - that trap arm will be approx 3' long - I...

Hey So - taking out built in tub to replace with freestanding - need some help on the wet vent as think what is there is weird/wrong. Thanks in advance - learning a lot as an first timer. Currently there is a 2" 12 ft wet vent running from the shower to the main 3" wet vent - and the tub 1...