Search results

Tom, It's funny how someone can be so insulting... (and probably deny it later) I'm not complaining about the price. But that being said, why do you think it's wrong to question it? Buying a Harley and never riding it, and paying an unfair/overcharged bill (if that was the case) are two...

Thanks guys. I just wanted to make sure that he was in line with what you guys might charge. I appreciate the help, as always. -Thomas

I just had my 20 year old Weil-McLain steam boiler repaired and got the bill. I was present for the entire repair so I know what was done, and how long it took. The boiler wouldn't fire. So he thought it was the thermocoupler. Replaced it, but still didn't fire. Then did some electrical...

thanks terry. i appreciate the help. have a great thanksgiving! -thomas

oops. here's the photo http://gallery.me.com/thomasmilewski#100052/photo i guess my real issue is that i've found chrome extension valves, but the 5" pipe is chrome plated- and i've never dealt with that. like this one: http://www.hardwareandtools.com/invt/u742403?ref=gbase can i...

here's a photo of my toilet supply line. i would like to dress it up and was looking for suggestions to get some chrome on it to match the rest of my bathroom hardware. i can't (or would rather not) remove any of the beadboard. any suggestions would be great appreciated. -thomas

thanks for the replies. i was leaning towards the oil filled baseboard for the reason that the oil wouldn't get hot enough to ignite anything that MAY come in contact with it accidentally.... and billy, thanks for the i appreciate the help as always. -thomas

safest electric baseboard heater? I am in the process of finishing my attic in my 1926 colonial. The conditioned space will be 25 foot by 12 foot. wall are insulated with R-30 and it has two windows on one gable end, one window on the other. the attic was parially finished and had a 6 foot...

thanks for the replies. one of my thoughts was to dig out for the shower only and have a step down stall. i've never seen one before though. are they common? anyone have any experience with them? i would love to get even more than 4" form the step down if possible..

I am thinking of remodeling my unfinished basement ( home built in 1926) and would like to put in a full bath (with shower stall , toilet and sink). The problem is that the height to the bottom of the rafters is only 6' 5". A toilet and sink wouldn't be an issue, but do you think i can get a...

i have an american standard faucet set in my bathroom on my second floor (only) bathroom, and when you try to fill the tub or turn the shower on to a warm position on the diverter, the cold water line (from the bathroom all the way down to the street source)shakes pretty hard for as long as the...

thanks for all the help guys. i've got this question about this vent stack: if the only one fixture (toilet on the 2nd floor) uses this stack as it's waste and vent, then can a toilet be added above it on the 3rd floor? all other fixtures in the house have/use a different vent...

sorry for my confusion guys. the main stack is a waste line for the toilet on the 2nd floor. the kitchen sink on the first. it's also a waste line for a slop sink in the basement. doesn't it ALSO operate as a vent for the toilet? thanks. -thomas

i am thinking about adding a toilet and sink to my attic and was thinking that it would make most sense to add it directly above the bathroom below it to tie into the existing cast iron stack. how would one tie into the cast iron stack? i'm not going to do it myself (i'll do the rest of...

Thanks for the help guys. I've sweated all my new bathroom copper. just didn't know what to do about the existing fitting in the other bathroom. It will be close to the wall- i agree, a real fire hazard. I'll be certain to use my flame shield and have an extinguisher on hand ;) Thanks again for...

But I've never sweated chrome to copper before... Anything I should know? Should I just rough up the chrome a bit, or remove all of it from the end? Thanks.

Thanks for the reply. How long is the sleeve on the watts valve? I need about 6 inches .... Thanks again. P.S. are you allowed to suggest a place to look for it online via this forum?

I have a toilet that was installed a few years ago- The copper supply line comes out of the wall about 6 inches, then a valve to a braided line to the toilet. Question is, how to make this look better? I'd really like to add a chrome 'tube' or 'cover' over the existing copper pipe if there's...

sounds like i should remove the lathe and plaster. i was afraid of that- it's what i thought at first. no biggie. only about 40 sq. ft of wall to remove. it will be worth it in the end. thanks for the help guys. -thomas

i would love to rip out all of this plaster, but i know that there aren't any studs on the window side as they are BEHIND the wide window molding.... i know because i opened up the bottom of this wall where the subway tile was.. down there, i added some vertical nailers so that i could nail...