Search results

I would shy away from vermont castings. From my understanding they used to be a great company with a very good product. They have been bough and sold numerous times in the last few years and quality has fallen shaprly. For info on woodstoves check out hearth.com.

I will be installing my water heater this week and need to know how far off the wall I can place the water heater. I have some radiant lines that I would like to run behind the water heater and I also need to get the venting in the joist bay. I would like to place the water heater around...

cattledog - thanks for the response. It does seem that I still have some homework to do. I am trying to do my heating as simple and economical as possible. We heat primarily with wood heat. We designed our house plan to be open to make wood stove most effective. That coupled with our relatively...

^^^bumpity bump bump

I am using flat panel radiators to heat my new home. I am trying to size my heat exchanger and pumps to run off of my water heater (Smith Vertex 76K BTU). My total heating load is 36K BTU per hour. I am using Veha radiators. There are 9 radiators on 8 zones (2 will be in series in the...

I do not have much area above the house (well i do but it would cost $$$ to get there). I do have room in the crawlspace. Can any of these pumps be installed underground? Would I still get my 36#'s if the power goes out? Is sound an issue? This is a forever home and I would like it done...

I am already running a 1" meter and 1" supply lines to the house.

I have a great structure, but no attic.

not sure if I am happy with my fixtures, as they are not hooked up yet. This is new construction and I am acting as Owner/Builder. I am close to being finished with my plumbing (minus fixtures). I understand that I am losing a lot of pressure due to my lenght of run and increase in...

So, I just got my water turned on and threw on a pressure gauge right by the house. I got 36 lbs of pressure. I was hoping for more but expecting less. I am on our towns water system, using 1" pvc through a 1" meter. I have a 450' run with about 125 vertical foot climb. Is 36 lbs enough...

from my limited experience of installing wirbo pex in my house, i would say no.

So I am finishing up my rough-in plumbing and need some direction on the best way to finish up at the shower valves and hose bibs. I am running 3/4" wirsbo pex to both fixture types. I was planning on going pex to copper and then copper into the fixtures. The shower valves have male and...

jadnashau - thanks for the comments. We are not in a super cold climate with an outdoor design temp of 17 degrees. We also use a woodstove as primary heat. Due to those factors we will be using a water heater (AO Smith Vertex) with a heat exchanger to run the radiator side. All the radiator...

I plan on using flat panel radiators for my new home. I was originally going to do underfloor radiant and I have a decent understanding of the zone mainfolds, flow pumps, controls, ect. for underfloor. I am assuming that with panel radiators with thermostatic valves the mechanicals are...

i will look into the extended warranty. thanks! :)

as far as AO Smith goes it is all I really have "inexpensive" access to. I am building as an owner/builder and my buddy was kind enough to put me on his cash account at the supply house. I get around 40% off list, which is better than I can get anywhere else. The supply house only carries AO Smith.

Does anyone have experience with the AO Smith Vertex water heater? My plumbing supply house only carries AO Smith and I am trying to decide between the Vertex and a standard powervent unit. There is about a $450 diffence with the Vertex being around $1450. I will be using it for my DHW and...

srdenny, thanks for the reply's. Vent termination is one of the reasons I want to place the WH in the basement. Vent termination is difficult in the utility room due to windows and overhangs. I live in rural north eastern california mtns, Burney to be exact. No problems what-so-ever with...

I will be running aquapex (wirsbo) with the propex tools. The longest hot water run is about 40' to the kitchen sink. So could I use 3/4" lines as my main trunk lines? or should I use 1"? With 3/4" trunk lines, I was concerned about pressure drop when using multiple fixtures. My carpenter...

ps. I am not against I recirculating system for the hot water side, if it is simple to do.