Search results

Ok, powered the pump off. Drained the tank - little to nothing came out. Bled air out of the pressure tank until it showed about 28 psi. Ran water from a faucet and I guess it acts normal now. The rate at which I see pressure drop from 50 to 30 is smooth and slow. That seems strange to me. The...

I have a 30/50 switch and a 20 gallon pressure tank. During the last two weeks or so, I noticed slight but frequent drops in water pressure that go away after a couple seconds. Running water and I see the pressure drop from 50 to 40 relatively slowly and then drop off sharply to 30 and the pump...

I understand the water from the furnace is acidic, I haven’t tested mine. Other than that, is there any other negatives to using that water to put into a warm humidifier? Sorry if it’s a dumb question.

just as a follow up because I hate when people don't put the resolutions to their problems on forums - Part of the problem I think I was having with my softener was the feet that came with it for the plastic screen in the brine tank. On the one I ordered, it came with cones as feet but, they...

I'm gauging the softness via my dishwasher and via my hair in in the shower. Originally I felt that "greasy" feeling on my skin and I don't now. Iam also aware of stiffness of my hair in the same measure. Not anything like when I had pretty much 85 grain hardness to wash with but, off the top o...

So I can add 9 gallons of water to the brine tank, wait 3 hours or so for it to dissolve salt and then run a regeneration cycle. Repeat for the second tank. I wrote all this, this morning and was trying to read about the efficiency, and read something about setting it for 6 versus 8, thought at...

I have a couple more questions. 1 - I would like to regenrate both tanks completely, the full 96,000 grains each, can you tell me what settings would do that, then I would manually regenerate both tanks and start over fresh with the current settings that have beem suggested. 2 - Does the (BF =...

Works. Used up the hot water and now the water is soft. Whoo Hoo!. How nice is that. Thank you very much.

The BFLC label says 0.5 GPM. There is a white label and one like yours that I can't make out. My water seemed like it is getting harder. I had about 18 gallons left with the new settings. I regenerated it and it never seemed to draw water from the brine tank. - the cycle started with the water...

Hah, bold = roar I guess. It's the way I tried replying, I was trying to on comment #23 of this. I made comments in the reply, wanted to use highlighter on my comments, couldn't find it, used bold instead. Posted it and saw the way I had replied, was minimized. So I figured no one would really...

My real question is why with the settings I had, that the system cycled through both tanks new and was fine but, after each tank was on it's second run of normal use, I could tell the water was harder and I'd get some of the frosting type look on glasses in the dishwasher. That's my main...

"IF your BLFC is 0.5 I would use the following. It may not be optimum, but its what I currently think. Let me know if you find mistakes." I attached a picture Injector as 3? - This is the Bflc Drain Flow 50 or 30? gpm. The number isn't perfectly legible to me. The capacity is 96,000 per tank

Setting it per the settings you suggest changes the current display of gallons remaining from 1017 to 705.

I replaced the softener with a 9100sxt, 96,000 grain dual tank. I used the water through the first tank until it cycled, used the water through the second tank until it cycled. I can tell that the water now though, isn't as soft as the first two times, having the 2 tanks brand new. So, I figured...

I'm sure I can get something and install it but I don't have a sense for what's a good system or just an overpriced one. My plumbers quote of--- (1)IMPS-1054 Impression Plus with air filteer & 1-clair Chlorination tank and (1)IMP 1354 Twin Impression Plus twin softener--- I'm not sure what that...

I got the test results back. I went through and took out all the results that were "None found (acceptable result)" and am left with this: Test Result Units Boron, total 0.22 mg/L Calcium, total...

I'm surrounded by farm fields and so I wanted to see "everything" including some other chemical concerns I have. Figure I'd just start with that test.

I mis-typed. Haven't ordered anything yet. That should've been "equipment I was quoted". I got the 360 test but haven't had a chance to do it yet. Got it the night before I traveled.

Well, overkill I suppose but, I ordered the 360 test.

My 32k softener is still going. Haven't ordered a test yet. I bought the UV light because, why not? I bought it to kill microbes, if any. I was really hoping somebody could tell me more about the models of the equipment I ordered. I have a brochure but I didn't seem to find to much in the way of...