Search results

  1. crtbilly

    Utility sink/water softener discharge.

    Could I use something like this? 3" PVC DWV Sanitary Tee w/ 2"Right Side Inlet PVC DWV Spigot x FIPT Cleanout Adaptor with Plug
  2. crtbilly

    Utility sink/water softener discharge.

    Got it! Thank you for taking the time, I really do appreciate your help.
  3. crtbilly

    Utility sink/water softener discharge.

    Thanks Reach! I really appreciate you taking the time. I do plan on adding a standpipe. I have a water softener and a condensation pipe from a hot water heater. Was gonna do it just like its picture above plus the AAV. oh, not sure if you saw in my drawing the red line i drew? Sorry for the...
  4. crtbilly

    Utility sink/water softener discharge.

    Hello all, I wanted to move a utility sink in my basement to a new location. Attached is the picture of the pipe i would tie into. It currently services a kitchen sink and a dishwasher and is vented at the sink to the roof. I was planning on using an AAV but not 100% sure it is necessary if i...
  5. crtbilly

    Boiler water feed/inlet line questions.

    Thanks jadnashua. I don't believe I have any leaks but I honestly can't say. I'm always looking for drips or water marks from leaks. I will try the shutoff after valves. See if I stop having to bleed air. If I was to have a leak some were, what should i watch for on the boiler. The pressure...
  6. crtbilly

    Pump Sizing suggestions

    Yeah, the old man was key in pulling and dropping the new pump. Thanks again for your help.
  7. crtbilly

    Boiler water feed/inlet line questions.

    Hi Everyone, I seem to be having issues with my backflow preventer valve. If I have the water shutoff open I will get drips coming from the vent. If I close the shutoff after a few weeks it seems it creates a vacuum on the vent and draws air into the system. From what I have researched its not...
  8. crtbilly

    Pump Sizing suggestions

    Sorry everyone for no conclusion update. Like most thinks I waited until it failed completely before tackling this. Like always it happened at the worst possible time. Had my parents in town, mom was showering at the time of course and no water. Lol....... anyways I had everything ordered and...
  9. crtbilly

    Pump Sizing suggestions

    Hey valeman, always appreciate the input. Did you see the chart I attached. Did I miss something or based on the data in the chart you believe it not capable. Thanks
  10. crtbilly

    Pump Sizing suggestions

    Hey valveman, thanks for the reply. Are you suggesting I lower my pump from 215' to 265' and up the size to 1 h.p.? I think my postings have been confusing and I apologize for that. My pump currently is not set at that depth according to the info I have. The depth your referring to is from...
  11. crtbilly

    Pump Sizing suggestions

    I put the wrong chart for the pump. This is the non high head.
  12. crtbilly

    Pump Sizing suggestions

    Thanks LLigetfa, I appreciate you taking the time. I guess I will call the well/pump company and confirm my current pump depth. I believe I did, but I have had so much info I may have confused myself. When well was drilled they did a pump test. Hours pumped: 3 hrs pumping rate: 10 GPM Method...
  13. crtbilly

    Pump Sizing suggestions

    Thanks Reach4 and Boycedrilling, I really appreciate your suggestions and insight. I have been trying to do some research on makes and models of pumps and I'm more confused than ever. Boycedrilling, Are you saying if the pump was moved to 100' instead of 200' or if the pump draws down to that...
  14. crtbilly

    Pump Sizing suggestions

    Thanks for the reply and sorry for the missing info. Some time I have trouble with my written words and what's in my brain. 1) it only runs for a few seconds before cutting out. 2) when it turns on at 40 it builds pressure up to 50 before cutting out. If you wait long enough it will make it to...
  15. crtbilly

    Pump Sizing suggestions

    Hello Everyone, Long time reader first time poster. Current setup from the information I could piece together from well report and last pump supplier. Well drilled YR: 1994 Well casing diam: 6" Well depth: 300' Water level from surface: 54' Pump depth: 200' Current pump: sta-rite 3/4 H.P...
Top
Hey, wait a minute.

This is awkward, but...

It looks like you're using an ad blocker. We get it, but (1) terrylove.com can't live without ads, and (2) ad blockers can cause issues with videos and comments. If you'd like to support the site, please allow ads.

If any particular ad is your REASON for blocking ads, please let us know. We might be able to do something about it. Thanks.
I've Disabled AdBlock    No Thanks