Search results

  1. Neshco

    Airlock!? or....?

    Hi and thank you! Here is a pressure, in average 3,5, but can drop to the 2,8 all the way to the 4. Bathroom is renovated 2 years ago and all taps are new, and very high quality. Ok, maybe some are not good (sink have 2 on the same line) but I am not sure that 2 taps became bad at the same time...
  2. Neshco

    Airlock!? or....?

    This happen before, a year ago. Water in my bath tub just stopped running, like someone cut the cold line. I found googling that it is maybe airlock problem and what I need to do to "unlock" it. Advise was to open both cold and hot water in the bath tub and with the hand palm press tap to...
  3. Neshco

    New Position For Old Water Softener

    Got it! Ill get back with the results as soon as circle of regeneration is closed. Thank you!!!
  4. Neshco

    New Position For Old Water Softener

    Does this help? Or to check somehow directly on device?
  5. Neshco

    New Position For Old Water Softener

    Just checked with the lamp height of the resin in the tank. It is 63cm from the floor to the top of the resin, which is approximately 25 inch. Calculation say that it is 1,5 ft3. Hmm. Do I need to change some settings accordingly?
  6. Neshco

    New Position For Old Water Softener

    Thank you for pointing that up. I have talked with the seller recently about eventual replacement of the resin and he confirmed that there is no gravel in the tank, only resin. He also told me that there is 2ft3 of the resin and in case of replacement I would need 2ft3 of it.
  7. Neshco

    New Position For Old Water Softener

    4. Thank you very much for clarifying this to me. There is no doubt about resin volume, it is 2cuft, I have checked with the guy who sold me the device price for eventual resin replacement and there is for sure 2cuft of resin. Also, found sticker on the tank and it is for sure 12x48 inch...
  8. Neshco

    New Position For Old Water Softener

    1,2. Well, not sure if we done it correctly then. Its filled with water and regenerated within few hours and now is in production. :confused: 6. Yes it is in grains (gpg), I kept settings like that for easier following you guys and left it like there until today. Hardness is measured with...
  9. Neshco

    New Position For Old Water Softener

    Hi everyone again, I need to please anyone willing to give me advise regarding one potential issue. I have already asked for advise here and get professional help and advises few years ago regarding adjusting my Fleck 5600SXT device which worked flawlessly until recently, when authorities...
  10. Neshco

    No cold water on sink and bathtub faucet

    Got you all guys, Ill try flush it with angle stop removed as soon as I get some free time. Meanwhile, got cold water back on a bathtub too. I hope you are right about this, because, if I am right, that is much bigger problem then debris or angle stop issues. Thank you for all advices and ideas...
  11. Neshco

    No cold water on sink and bathtub faucet

    Thank you all for tips, just to clarify few things. Bathroom and installations are new, just 2 months since we start using it and there was no any other problems with it then this. Sink have stop valves, flat washer type, but bathtub does not. There is a flexi pipe connected directly to the 18mm...
  12. Neshco

    No cold water on sink and bathtub faucet

    Thank you Terry for tips, but I am not sure that it is a case because there is 0 flow there. If there is some kind of dirt, it would at least have some drops of water, but that is not the case. There is literally no a single drop of water. Plus, unlike last time, now I had exactly same problem...
  13. Neshco

    No cold water on sink and bathtub faucet

    Have finished my self my bathroom on the upper floor of my house approximately two months ago. Have used pipe in pipe system, Wirbo/Uponor q&e connection. Everything worked just fine until about a 2-3 weeks ago when suddenly stopped run cold water from the bathtub faucet. Have tried to Google...
  14. Neshco

    5600sxt Settings - Very Salty Water After Regeneration

    Hmm, when I asked you for advice some weeks ago, you told me to check which valve is in question there, and I dint know that I can read it on the case of the head and I disassembled it. There was only white plastic thing, dont know if that is what you meant by white, blue or red? Is it possible...
  15. Neshco

    5600sxt Settings - Very Salty Water After Regeneration

    Got it. Now I understand that :) This is what I have there. Regarding brine fill, to be honest, I was not all the time beside device during this 60 minutes, so it is possible that all brine is sucked out in 15-20 minutes. Next time I'll follow it thoroughly to confirm. Thank you very much...
  16. Neshco

    5600sxt Settings - Very Salty Water After Regeneration

    Dear sir, I have readjusted settings by your instructions and it appear that everything is in order now. Have tested TDS again and it is like 430 now, guess it is ok. There is no salty taste anymore. During BD, I think that all brine was sucked out after maybe 30-40 minutes. Is that normal...
  17. Neshco

    5600sxt Settings - Very Salty Water After Regeneration

    Absolutely possible. Guess Ive done that. Will see tomorrow. Before I readjust settings, just to check. Is C=43.1 correct value? Because this is 64k capacity. There is also in system info "cubic ft resin = 2 ; ft3 resin = (nominal grains)/32,000" Is that ok? Because you havent change BW, Bd...
  18. Neshco

    5600sxt Settings - Very Salty Water After Regeneration

    Hi and thank you very much for response. Just checked the counter, it is on 2601 gallons left, and no, it does not count down when water is not in use. It look pretty much normal when in use. I didnt expect to see regenerated system this morning when I woke up. Especially we didnt use water...
  19. Neshco

    5600sxt Settings - Very Salty Water After Regeneration

    Yesterday, I finally installed my Fleck 5600sxt bought last year. I have tested hardness after installation and it was zero. Everything was just fine. This morning, after regeneration, I found that water have very salty taste. Guess, I didn't adjust something correctly. I would like to...
Top
Hey, wait a minute.

This is awkward, but...

It looks like you're using an ad blocker. We get it, but (1) terrylove.com can't live without ads, and (2) ad blockers can cause issues with videos and comments. If you'd like to support the site, please allow ads.

If any particular ad is your REASON for blocking ads, please let us know. We might be able to do something about it. Thanks.
I've Disabled AdBlock    No Thanks