Search results

Ok thank you, would a driller be able to tell if digging deeper would reach such a formation? There are only a couple of drillers in our area and they should know the aquifers by now - our driller specifically has also done two neighbors up the hill and our provincial well records are all...

Would our 300ft depth count or do you mean deeper than that? In your experience do people who deepen their wells by 100ft or so improve the yield or does it just make a bit more storage space down there?

The tank is what we're going to do for now anyways, it will be outside in a 'tank room' but we're going to redirect just enough heat to it to prevent freezing. Another neat trick I noticed someone else around here do is add a 'circulating branch' to the tank output side - anytime the second...

I've been troubleshooting a five year old well and have noticed what seemed like a slowing of the refill rate in the last year or two. I've also noticed a drop in the static head level since it was installed. When drilled we had a static head of 40ft and a refill rate of about an hour, I just...

And what is the common method for installing a CSV when the well is outdoors without a well house and all connections are buried about 3ft down? We don't have the worst winters but it is Canada so frost is an issue from November to April.

Thank you, we already have a 2500 gal tank up at the second house - it just isn't tied into the system right now. This used to be used for water delivery before we ran a water line so we could share the well. It would be a fair bit more work to bury it somewhere close to the well since it is...

The pump is a 3/4 5GPM. The cycle sensor does shut the pump off when this happens, I have the reset time set one hour. The original installer noted the well yielded 2GPM . Would a CSV still be able to work with this?

Just to add, I am pretty sure the pressure drop is primarily the result of me using the yard hydrant to fill a pond overnight - I have it on a timer and it only comes on for about 4 minutes at a time spread out at 1 hr intervals. But this is the only major change between the winter (when we...

Here is our setup, I got some help here last year regarding a recurring dry pump situation (thank you very much!). Everything worked great over the winter but I think that our combined houses water use (with little gardens, etc) in the summer is still affecting the system. Here is an image of...

Thanks, I will try that again - I do remember backwashing as we installed a hydrant right by the well and I cycled it for quite a while before sending the chlorine through the rest of the system. I didn't do the vinegar though.

I'm going to check the drain/overflow again as well as the supply lines - I can't seem to smell anything if I put some water into a glass and smell it. I'm not 100% sure it is the water after all, I just thought that dealing with the sink once would have removed that as a source.

We didn't have any smells when we were on the shallow well, it didn't start until we switched to the new one. I'm not sure it has anything to do with it but I thought it might be relevant.

The well is 4 or 5 years old now, I tried sanitizing based on something like this guide about a year after the well was drilled when I first tried to figure out the smell issue. I think the process did have a short term effect but the smell was back within a month or less, I have repeated the...

Ok, I will try that too thank you. Would older pipes potentially cause the same thing? The house is plumbed with poly b, probably 20-30 years old.

Initially I thought it was the drain/sink/overflow so I replaced the sink and the p-trap. The smell just started when we switched from our shallow well to a new deep well.

Thank you, that was kind of the direction I was thinking of starting with. Would under the counter make more sense than right after the pressure tank so it filters everything? I came across aeration solutions as well, but they all look quite pricey. I have a spare circulation pump, would a...

It dissipates after a while when the water is running, it is definitely strongest right after opening the tap. No issues from the toilet, nor smell from the toilet water. The shower (it's a walk in) valve is a few inches higher than the sink, but I just turned it on and it doesn't have the...

It seems like primarily cold water, when I run the hot it smells a bit but seems to subside faster. The shower head next to it is the only higher fixture but I don't notice the same smell with the shower on. The fixture doesn't smell until the water in turned on. No, it smells pretty normal...

I am working on sorting out an issue with our well water but google searches aren't coming up with this particular situation. Our well water, which is hard water (no iron stains, etc but eventual mineral buildup on the faucet screens), has a certain smell to it - but it is really only...

Just wanted to update in case a future internet search leads to this thread. It was a combination of a failing hot water tank, T&P valve (in the upper second house) and the 'low pressure cut-off' pressure switch. The hot water tank was leaking, as was the T&P valve, but intermittently (and at...