Search results

Follow up: I realized what the real problem was today, although the shutoff valve, regulator and steel piping is all 3/4" the CSST that is feeding it is 1/2". The heater will not operate on a 1/2" line. I had to dig out silicone and get inside of the conduit that they had sleeved the CSST in to...

I understand this question more clearly now. For probably the last 15 - 20 years the natural gas meters that are installed here are 2psi with the required regulator at each individual appliance.

if the regulator is 7" wc - 11" wc wouldn't I be able to read it in inH2O on the manometer at the control valve?

Thanks, I will check that. It is a house but around here it is most likely a 2psi meter, they quit putting in the 7" meters quite a few years ago. not sure why. But I will double check.

That is my suspicion also but this is a good customer of mine and I want to do what I can to help.

As I stated in the post, it is a natural gas regulator. It is not in the house, it is outside at the pool heater. I do not have the old regulator but based on what I now know in regards to earlier HO comments it was doing the same thing.

If it is 200 PSI poly tubing then there is a good probability that it has collapsed somewhere. I agree with TUGHILLRZR that 2o' lengths does not make good sense (unless you as the homeowner actually installed it yourself). There are way too many joints that can cause issues. I do hope that you...

The one thing that I did not see in any of the posts is what type of pipe your main line is. Do you know?

Yes, you can use air pressure on that much line it will just take longer to pressurize. For safety reasons do not let the pressure exceed 100psi. If 100 psi does not blow it out then you have a bigger issue.

I have had instances where the city shut off the water to replace a meter and when the water was turned back on it could not reach the house. There was a section of the pipe that had kinked where it entered the foundation. This was caused by the home settling. When the water was shut off the...

If there is low flow at the hose bib that is immediatly after the shut-off but it is not regulated by the PRV then the issue is not the PRV. There is a possibility that the shut-off valve has sediment obstructing it. You may have to shut off the meter and replace the main shut-off. You may even...

I do not install pool equipment but a customer asked me to replace her natural gas regulator that serves her pool heater. I asked why she was wanting it changed and she said that her pool guy told her she needed a new one. I replaced the regulator with the exact same type, 3 weeks go by and she...

I like the cutouts; a picture is worth a thousand and one words...

If it is a dedicated cold water pipe, does it not have it's own shut-off? If it does then just don't use the provided two-way valve, connect directly to the shut-off.

Nice job

In the middle picture if you were looking straight on at the sink tailpiece is the trap adapter completely to the left of the tailpiece? Is it possible to swivel your trap towards the front left of the tailpiece and have the trap arm pass it? If so just add an extension if the trap armis not...

They do make these, you could cut one in half and use it to make your trap work. I personally am not a fan but it is an option. This pic was copied from Lowes website.

I understand that but at this point as much time as you have taken to produce a good looking job I think I would rather patch the hole then leaving the plumbing looking off-kiltered. Especially since you have easy access to it and you are going to be cutting pipes anyways. From what I have...

If you have access to the back side (judging by your picture you do) then just cut out a section of the pipe and couple back together to relocate stub out; then it will be right and you can just patch the small hole that will be there. Is that an option?

On some kitchen faucets that have a sidesprayer they will give you the option of not using the sidesprayer; if that is the choice made then you would not attach the sidesprayer but instead you would attach the piece that you have pictured there.