Help with adaptor for old 1960s ball end shower arm

Discussion in 'Shower & bathtub Forum & Blog' started by gemgem, Jul 28, 2012.

  1. gemgem

    gemgem New Member

    Messages:
    6
    Location:
    houston
    The backstory:

    My parents bought an old house from the late 1950s, complete with a shower arm with a ball end. My mom would very much like to have a handheld shower head, but of course no one makes shower heads for our type of shower arm anymore. We would love to just change out the shower arm to the standard 1/2" one, but my dad is afraid we'll break a pipe in the wall (which we just can't afford right now).

    The problem:
    I went out and purchased an adapter for our 1950s American Standard shower arm, which changes it from a ball end to the standard 1/2". When I screw the adapter + the new shower head into the captured nut, it only screws maybe halfway down the adapter's threads. This results in an extremely loose-fitting captured nut (when the original shower head is screwed in, the captured nut fits snugly against the ball end), and water squirts everywhere from above the captured nut. The only way to get a decently tight fit between the adapter and the captured nut is to stack about 4 or 5 o rings between the adapter and the ball end. My problem with this method was that if the o rings twist or shift, water comes shooting out again.

    I do get really good pressure in the new shower head (even with the extra spray of water from the shower arm), but I'm afraid the water will leak back into the wall and cause rotting.

    Does anyone have any ideas of how to help the adapter get a good seal with the shower arm?

    I hope the pictures below aren't too big.

    1.jpg

    The adapter (and where the o rings sit):
    2.jpg

    The old shower head:
    3.jpg

    The adapter screwed in (only 1 o ring inside):
    4.jpg

    The old shower head screwed in:
    5.jpg
  2. jimbo

    jimbo Plumber

    Messages:
    8,997
    Location:
    San Diego
    There were a few common ( all different!) ball end shower arms. AmStd and PricePfister were two. You may have the wrong adapter, but the best idea is to replace the shower arm.

    [​IMG]
    Last edited by a moderator: Jul 28, 2012
  3. gemgem

    gemgem New Member

    Messages:
    6
    Location:
    houston
    Do you happen to know if "Standard" (how my old shower head is marked) is how American Standard used to mark their products? The handles that are with this shower were confirmed to be American Standard in another thread, so I'm hoping it's a matched set.

    We really would love to change the shower arm, but we can't afford risking a broken pipe right now.
  4. jimbo

    jimbo Plumber

    Messages:
    8,997
    Location:
    San Diego
    Yes, going way back....I think pre-early 50's, the name was Standard. That badge was revived on some retro items in the early 2000's. I still suggest that you stop fighting city hall on this and just replace the arm.
  5. gemgem

    gemgem New Member

    Messages:
    6
    Location:
    houston
    Thanks, we'll see what we can do.
Similar Threads: Help adaptor
Forum Title Date
Shower & bathtub Forum & Blog Had to remove part of my subfloor, now I have NO idea what to do...please help! Friday at 6:36 PM
Shower & bathtub Forum & Blog Help in Identifying Diverter Valve Stem Jul 14, 2014
Shower & bathtub Forum & Blog Request - help with shower faucet removal and install Jul 11, 2014
Shower & bathtub Forum & Blog Tile Tip of the Day - tidbits of info to help hone your skills Jul 10, 2014
Shower & bathtub Forum & Blog I need help with the right hose for this head Jul 8, 2014

Share This Page