Any suggestions on my dishwasher?

Discussion in 'Plumbing Forum, Professional & DIY Advice' started by nanllyn, Sep 8, 2005.

  1. nanllyn

    nanllyn New Member

    Joined:
    Sep 8, 2005
    I have a questions about my dishwasher. We just moved into a 60+ year old house on well/cistern water and septic system. We have pretty good pressure at my sink faucet but when I use my dishwasher on hot water it takes approx. 7-8 hours to complete a cycle. Also if I use powder soap with the hot cycle the powder is left on the glasses and some of it is still powdery which leaves me to believe they have not been touched by water. If I use cold water it seems to finish in approx 2-3 hours. This is a 3 year old dishwasher and we were told it worked just fine. Any thoughts on what might be wrong or what to check.
     
  2. Dunbar Plumbing

    Dunbar Plumbing Master Plumber

    Joined:
    Apr 18, 2005
    Occupation:
    Service Plumber, Outdoor Temperature Relief Owner
    Location:
    Northern Kentucky/Greater Cincinnati Area
    Check the isolation valve that serves the hot water line to dishwasher, probably calcified up.
     
  3. Sponsor

    Sponsor Paid Advertisement

     
  4. jimbo

    jimbo Plumber

    Joined:
    Aug 31, 2004
    Location:
    San Diego
    I am confused because I never saw a DW where you had the option of using cold water. There is only one water inlet. Please explain.
     
  5. nanllyn

    nanllyn New Member

    Joined:
    Sep 8, 2005
    Some more information

    Okay, I have a Frigidaire Ultra Quiet III. It has a high temp wash. If I push this button it takes approx. 7 hours. If I turn it off it doesn't take as long approx 2-3 hours. I opened the dishwasher once with the high temp and steam really came out. When I opened it when I had not choosen the high temp option, no steam. It may not have been cold but it wasn't hot enough for steam to come out. That is what I meant. Maybe the dishwasher is toast and I need a new one but if it is repairable I sure would like to.
    Thanks again for a great forum and helpful people.
     
  6. RioHyde

    RioHyde Plumber

    Joined:
    Sep 24, 2004
    Occupation:
    Plumber
    Location:
    Cincinnati, Ohio
    I'm with RUGGED. I'd first check the valve and the waterline to the dishwasher. Really sounds as if you're not getting enough (if any) water to the unit. There could very well be a calcium buildup in the valve restricting waterflow. If you have full flow from the valve through the waterline then I'd call out an appliance repair company.
     
  7. thezster

    thezster New Member

    Joined:
    Jul 18, 2005
    Occupation:
    Retired young... day trade stocks - and to keep bu
    Location:
    Fort Collins, Colorado
    I'm not a dishwasher expert but..... (and someone feel free to chime in here... )

    If you choose the "high temp" option, the dishwasher adds it's own heating element to the process, heating the water to a level higher than that supplied by the hot water heater, right? If so - is the "high temp" controlled by a thermostat? Is it possible her heating element is taking "forever" to get the water to temp, thereby causing the extended time to do a load?

    Nanilyn::: When you choose the regular temp option, does it really take two or three hours... or does it just seem like it.... My dishwasher takes about an hour to run a cycle..... though sometimes it seems like two....
     
  8. jimbo

    jimbo Plumber

    Joined:
    Aug 31, 2004
    Location:
    San Diego
    You may two problems. First, there may be an obstruction somewhere causing slow fill. Second, depending on the layout of your pipes, the DW may be filling with COLD water, By that I mean that it only uses a few gallons to fill, and these first few gallons out of the pipe could be cold. Try this: Right before running the DW, run the kitchen tap long enough to get hot water coming. Now start the DW. Even with this, by the time the next cycle comes around, it may have cooled off some.

    If either of the above situations is true, then the PreHeat option of the DW will further slow down the process, or you could have a failing heater element.
     
Similar Threads: suggestions dishwasher
Forum Title Date
Plumbing Forum, Professional & DIY Advice How to replace inline sillcock? Need suggestions. May 12, 2015
Plumbing Forum, Professional & DIY Advice Looking for sink/disposal drain suggestions. Sep 8, 2014
Plumbing Forum, Professional & DIY Advice rework problem with an existing toilet flange - help suggestions appreciated Apr 25, 2014
Plumbing Forum, Professional & DIY Advice Kitchen sink drain - is it done correctly? Looking for your comments and suggestions Apr 7, 2014
Plumbing Forum, Professional & DIY Advice sewege pump and ground water leak Suggestions needed Apr 3, 2014

Share This Page