Recent content by chris1044

Casing was measured on I.D., and brass barb fitting was used on the poly. Hot water was used to heat the poly as well....did this because the f'er wouldn't fit by hand:D...had no idea it was standard practice.

I ordered my stuff from ohio pure water roughly 1 year ago....I'm in MI, but it showed up within 2 days, and they had the best prices I could find. After the installation, I still had some smell in the water, so I e-mailed them (iron smell, not sulfur) and they were very helpful on walking me...

My casing is a 5"....per my tape. As of right now, the entire thing's back together, and the house is pressurized. I ended up leaving the pitless adapter as it turns out the threads in it were brass. Long story, but from what I can see, the brass/galvanic sections are isolated by rubber...

This is my pitless adapter: http://www.baker-mfg.com/domestic_new/pitless_adapters/Snappy.html Why on earth would ANYONE choose to use this piece of shit? I see ZERO advantages, aside from possibly cost (not likely since I'm sure sales volumes are way low). Yes, lets put something that will...

The pitless adapter is in fact galvanized steel...a magnet sticks right to it. It's bolted around my 4.5" steel well casing like a muffler clamp would. It doesn't look like there's a whole lot of places for it to corrode through at, but still. I could replace the straight/90*/straight...

I'm located in MI, bought this house a year ago, and my well water level is roughly 80' deep (checked by removing cap on well with a weight/string). Neighbor says well was put in 20 years ago or so, doesn't know if the pump has ever been changed. I don't have a well log from the...

Numero uno: I don't think my SFR GMP is greater than 12gpm....I have 3/4" CPVC through the home. Its 2.5 bath...are you saying I need a larger softener? Numero two: I know i don't need a turbulator...but if it helps, why not. Gravel underbed? This is the first I suppose I've heard that...

Excellent...thanks for the response Bob! I had a hunch that going to big isn't necessarily a good thing here. 1.5 Cu Ft Fleck 7000, SST resin, w/turbulator is what I'm going to be purchasing. I'm going to look into various connections avail out there today...will post pics/updates after I get...

So I'm positive I'm going with a fleck 7000 SXT, 64k grain capacity. I estimate I'll only need 48k, but I want efficiency and I don't want to be undersized...negatives in doing this? I found some with a "bypass" available at 3/4"....this the same as inlet/outlet connections? Also, what...

Here's another question for you...my inlet line on the plumbing is 3/4" CPVC. The Fleck 7000 has a 1" inlet flow valve. Obviously I could redo my inlet line from the well bladder to the softener as 1", but do you know of any 3/4" to 1" adapters for CPVC? If not, any thoughts on the SXT valves...

Here's another question for you...my inlet line on the plumbing is 3/4" CPVC. The Fleck 7000 has a 1" inlet flow valve. Obviously I could redo my inlet line from the well bladder to the softener as 1", but do you know of any 3/4" to 1" adapters for CPVC? If not, any thoughts on the 9000 SXT...

Bob, you have a PM...

Bob, You seem to genuinely be willing to educate me on what I need, which is why I'm sending you a PM. Having said that, I'm fairly confident that a Fleck 7000 with SST resin is what I want to go with. Any suggestions on where to purchase this? You stated it can be had for under 700...

Is there really any benifit for a twin tank set up in my situation? Longevity? I don't need water 24/7, and because of that, I can't see any real reason to upgrade. Additionally, if I get different resin, how does one go about changing that himself...remember, I'm a noob here....any qualms...

As I have...The water is approximatley 30gpg hardness. It has 2ppm iron in it, with a little bit of "iron" smell. It does not smell like sulfur, nor did any of the analysis detect hydrosulfuric gas (or whatever the chem name is that causes rotten egg smell). Furthermore, there isn't any slime...