Recent content by 8888

  1. 8888

    Stat Battery

    Is there a way to pigtail a battery onto a stat that doesn't have battery backup? I need a way to supply it with just enough power if the house power goes out.
  2. 8888

    Air Handler

    I'm replacing an existing split heat pump and I would like a little knowledge BEFORE contractors come out to give estimates. I know which condenser I want, but I'm confused regarding the air handler portion. Apparently there is not a matching set (Condenser 'A' gets paired with Air Handler 'A')...
  3. 8888

    Stat Test

    I have a new stat that I would like to explore the menus to see things like Firmware version etc. but I don't want to install it yet. Is there a safe alternate way to power it up, but not wire it to the HVAC equipment?
  4. 8888

    Tub Drain Solution?

    I could use your help with options for installing the drain on a freestanding tub. The install is on a concrete slab, so what I have leftover from the previous tub is a square hole in the slab, dirt below, and the old P-Trap in the hole. My concern is that the install instructions ask you to...
  5. 8888

    Moving a circuit

    Would any electrical pros check me on this please. I have removed a jet spa bathtub, so now there is a receptacle that I don't need. On the bathroom end is a GFCI receptacle where the pump plugged in. On the panel end is a 20a breaker. Yellow romex connecting them. This appears to be a...
  6. 8888

    Venting AV Exhaust

    I could use some feedback on options to terminate an AV closet exhaust fan. It’s an inline fan located in the attic, and since it’s only venting warm dry air I don’t think I need to worry about moist air such as from a bathroom. Guesstimates: - the exhausted air from the AV equipment 90º-95º...
  7. 8888

    Dishwasher Power Cord

    I need to make a dishwasher power cord. New DW specs: 12a/1450w Min 14g 167ºf Current house wiring: dedicated 20a circuit [12g] 15a split receptacle [w/disposal] Q: Can I use ±6' of SJOOW [300v] & add a 15a plug? [the other end = pigtail to DW] Q: 14/3 [18a] or 12/3 [25a] Is...
  8. 8888

    Adding new receptacle and switch

    Chad, you have way too much free time trolling forums looking for fights. As the original poster I would ask JW to ban you from this post, as you bring NOTHING but a crappy attitude and a narrow minded point of view. I am officially requesting for you to get lost, go away. Nobody here wants to...
  9. 8888

    Adding new receptacle and switch

    Based on that statement this website should be shut down. I was under the impression this was THE place to "ask questions," so we can do it right. You have never validated your statements as to why one way is 'more correct' than another, or added an illustration to make your point more clear...
  10. 8888

    Adding new receptacle and switch

    - My reasons for drawing 2 over 3 has EVERYTHING to do with the number of wire nuts. If you have never installed a Home Automation switch or receptacle there are things to be aware of: 1) They are bigger [deep]. They limit the amount of space to tuck your wiring. I have installed many into...
  11. 8888

    Adding new receptacle and switch

    Some of us come to sites like this to gain knowledge that is BACKED UP WITH EXPLANATIONS and REAL EXPERIENCE, not "do it this way or your a hack". I have owned several homes and have seen many different wiring configurations all legal, all passed inspection. So I don't believe for a minute that...
  12. 8888

    Adding new receptacle and switch

    A long ground wrapped around the screw IS one wire, one screw.
  13. 8888

    Adding new receptacle and switch

    Is there a code that states '1 wire on 1 screw only'? If so I could: - make the ground entering Box3 x-long, and wrap it around the screw, then continue on. or - Pigtail all the grounds together at the ground nut [as shown] Any thoughts?
  14. 8888

    Adding new receptacle and switch

    Yes, that is correct. There is NOT enough slack to re-join the original Romex in only one box, so having 2 boxes seemed to be the only way. It doesn't need to look pretty, since the whole config is in the attic. The other LEG coming out of BOX1 is all the new wiring servicing the outlet...
  15. 8888

    Adding new receptacle and switch

    Now I'm more confused. I thought that a drawing would help visualize my setup. Here is another drawing. Notes: * Existing Romex is approximately 2' from Box 3, and once cut there will not be enough slack to do anything but box each end. * This is NOT a regular switch. It has 4 permanent wires...
Top
Hey, wait a minute.

This is awkward, but...

It looks like you're using an ad blocker. We get it, but (1) terrylove.com can't live without ads, and (2) ad blockers can cause issues with videos and comments. If you'd like to support the site, please allow ads.

If any particular ad is your REASON for blocking ads, please let us know. We might be able to do something about it. Thanks.
I've Disabled AdBlock    No Thanks